您已经添加该商品到您的收藏列表
从您收藏列表中删除此商品。
这家公司已成功添加。 查看我的收藏.
这家公司已从你的收藏夹列表中删除。
这家公司已被添加到您的询问车。
这家公司已从询价车中删除。
该商品已被添加到您的询问车。
该商品已经从您的询价车中删除。
商品/公司已达到添加至询价车的数量。
登入NEWPAGES
保持登入状态
每日登录奖励

恭喜! 你获得了今天的每日登录奖励!

5 NP Point这是您获得的奖励!
查看您的每日登录奖励

确保每天回来登入以获更多的奖励!
谢谢!

Back
Seni Jaya Logo
访客

Red Lion MP37CA00 magnetic pickup

23-Jul-2024
Red Lion MP37CA00 magnetic pickup
产品已浏览 30
产品规格
Red Lion MP37CA00 magnetic pickup Description of operation:- A Magnetic Pickup consists of a permanent magnet, a polepiece, and a sensing coil encapsulated in a cylindrical case. An object (target) of iron, steel, or other magnetic material, passing closely by the pole-piece causes distortion of the magnetic flux field, which in turn generates a signal voltage. The magnitude of the signal voltage depends on the relative size and magnetism of the target, its speed of approach, and how close it passes the pole-piece. Magnetic Pickups are most frequently used to sense passing teeth on a gear, sprocket, or timing belt wheel. They can also be used to sense bolt-heads, key-ways, or other fast moving metallic targets. Typical targets and resulting signal wave forms are shown below in Fig. 1. Selecting a magnetic pickup:- Selecting a magnetic pickup is a matter of matching a pickup to a gear (or other target), to provide enough input signal to a tachometer, speed-switch, or other device for operation at the required minimum speed. The open-circuit output from a magnetic pickup is directly proportional to speed, and once the minimum operating speed conditions have been met, increased signal will occur at higher speeds. The “1-Volt Threshold Speed” column in the Application and Ordering Table (next pg.) provides a convenient guide for estimating minimum operating speeds. This value is the linear surface-speed of a reference gear required to generate a 1-Volt peak, open-circuit output at an air-gap of 0.005". The reference gear listed for each pickup is near the optimum size for that pickup, as defined by the criteria in Fig. 1B. The RPM listed is for a reference gear with 60 teeth running at that surface-speed. Gears with larger teeth provide about the same or somewhat more output at the same surface-speed, while gears with smaller teeth or fewer number of teeth yield lower outputs. Figures 1C -1F need a very high surface speed to generate a 1-Volt peak. The “Minimum Gear Size” column lists the Diametral Pitch size at which the output drops to 40-60% of the output when the reference gear is used. Gears with very small teeth in relation to the pole piece diameter, deliver greatly reduced outputs, as shown in Fig. 1A. Threshold outputs when using targets other than gear teeth can be estimated by their relative size with respect to the reference gear teeth. For more information on gears, definitions and relationships, see the Sensing Gears Bulletin (LP0167). The 1-Volt Threshold Speeds are based on a 0.005" air-gap. In applications where this air-gap cannot be maintained or where the air-gap can vary due to eccentricity of the sensing gear, a correction factor can be applied from the curve in Fig 2. The effect of electrical loading is usually minimal at low speeds and low output frequencies, however, output voltage drop due to loading at high frequency or with low impedance inputs can be estimated based on the Output Impedance data. Magnetic Pickups are recommended for speed related sensing applications. They are not recommended for counting applications, since loss of counts will occur at low speeds. For devices not designed to accept a magnetic pickup input, the Red Lion Controls model ASTC can be used to convert the magnetic pickup output into an NPN open collector output. The ASTC can detect magnetic pickup outputs as low as 20 mV, which allows for operating speeds below the specified 1-Volt threshold speed.
发信息至 ENMARK (M) SDN. BHD.

谢谢您的询问!
我们的客服会尽快联络您。

如需咨询或问题,联系我们
总办事处

ENMARK (M) SDN. BHD. (166374-H)
Lot 8, Jalan Tembaga SD 5/2A, Bandar Sri Damansara, 52200 Kuala Lumpur, Kuala Lumpur, Malaysia.
Google Maps Waze

电话: +603-6272 3232
传真: +603-6275 8069

邮件: enmark1987@gmail.com, enmarkinstrument@gmail.com
网址: https://www.enmarkengineering.com
网址: https://enmarkengineering.newpages.com.my/
网址: http://enmarkengineering.n.my/

Powered by NEWPAGES